Answer 1
Unplug the wire from your phone charger, and then ruthlessly cut off the USB-C or micro USB and Lightning (depending on what model you have on your phone, you will be without power).
Cut off the wire’s sheath, then take out of the middle of the two wires that were used to connect to the charge port of the connector through which the phone was charged.
If you’re lucky enough, these two wires could turn red and black.
Remove the insulation approximately half an inch to leave two contacts exposed.
Make sure that the charge indicator and brand name appear on top.
Be sure to put the red wire carefully into the central orifice located at the top of your vape, and put the black one in the hole just located to the right of the middle one. While you’re doing this, make sure that the charge light and your vape’s name appear above, as stated in the preceding paragraph.
If everything has worked out properly, the green indicator should blink. It will announce that charging has started, and in a short time, you’ll be able to enjoy a second vapor with that beloved Vuse. While charging takes place, make sure you keep all of your vape and both wires in your fingers and be careful not to shake them. Sudden interruptions in the flow charging will not cause your device to become healthier.
Answer 2
Charging a vuse without a charger isn’t a very complex process. It’s a simple process and you have to do very simple steps in order to charge a vuse without a charger.
First of all, you have to take a “sharp knife” and a simple data cable. Then, you have to cut that data cable from an appropriate distance in order to detach the “Type-C” or “Android” pin from it.
After doing so, you will have to remove the top covering from that cable. In most cases, after removing the outer covering, you will see two different wires.
One of them will be +ve while the other one will be negative. If you have got Red and Black colored wires after removing the outer covering, then the Red one will be +ve while the Black one will be negative.
Removing covering from Red and Black wires or whatever wires you’ve got:
After removing the covering from the outermost wire, now you have to remove the coverings from the Red and Black wires or whatever wires you’ve got after that. After removing the coverings from the Red and Black wires, you will get metallic wires.
Now you have to pick up the vuse and the side that has battery light upward. Now you have to put the data cable into a charger(not necessarily a vuse charger. It can be a mobile charger) and plug the charger into the switch.
A vuse comes with three holes or what you call as the terminals. Now you have to put the +ve(Red) wire in the central hole which is the positive terminal and the -ve(Black) wire to the left of the central hole which is the negative terminal of vuse.
So all you have to do is to connect the +ve(Red) wire with the +ve(central terminal) and the -ve(Black) wire with the -ve(terminal to the left of the central terminal) terminal of the vuse.
By doing so, the charging light will lit up indicating that the charging process has successfully started. In order to stop charging, you simply have to detach the two wires from the terminals of vuse.
Answer 3
Can I Charge My Vuse Vape with a Phone Charger?
Yes, you can charge your vape with any of the android chargers or iPhone chargers if the chargers have a micro-USB and your vape model supports a micro-USB port.
However, another way of charging your Vuse without a charger is you can split open the charger’s charging port and expose its inner wires.
Now, connect the USB port to a power adapter and plug the adapter into the electric board and turn on the switch. Once the current starts flowing you can connect the red and black wires to the charging port as shown in the image below.
Once properly connected, you will see the charging light turn on and let you know that your vape is charging.
In case, you don’t have a phone charger available to you, you can go to a gadgets store and buy any portable charger, AUKEY 26500mAh Portable Charger is one of the best electric gadgets that you can purchase for under $100.
However, there are some things that you should keep in mind while you charge your Vuse without a vape charger, some of them are:
- In case there are other wires inside your charging cable – like green and white – then you need to cut them out, we don’t need them, we only want red and black
- Do not touch the naked wires when connecting the wires to the vape
- If you feel the vape is heating up, stop the charging at once
- There is a risk that the battery might explode, as there have been various instances where people connected an inappropriate charger to the vape and the battery exploded, PLEASE KEEP THIS IN MIND!
Frequently Asked Questions
1. What voltage should I charge my vape at?
A voltage of 4.2 is most commonly found in vape batteries, a nominal voltage of 3.7, and a voltage discharge cut-off between 2 and 3 volts can be an optimum voltage to charge your vape with.
2. How Do You Charge a Vuse?
Connect the Vuse’s proprietary charger to a power source (electric board, laptop, portable power adapter, etc.) and connect the charging port to the Quick Connect end of the charger. The charging light will turn green and your Vuse will start charging.
3. Is it Safe to Use a Phone Charger to Charge Your Vuse?
Please remember that Vuse produces proprietary chargers that should be specifically used to charge your Vuse vapes, and it is not recommended to use other chargers to charge your vape. You will not only be damaging a good and healthy charger but also run the risk of getting shocked or the vape’s battery exploding.